Skip to content
NewcastleConcreters
  1. Home
  2. Blog
  3. Concrete driveway and slab thickness

How thick should a concrete driveway or slab be?

Thickness is the number that separates a cheap quote from a sound one, and it is the one thing nobody can check after the pour. These are the published minimums for driveways, paths, patios and sheds, what the two local councils add at the kerb, and when the minimum is not enough.

Published 16 November 2026 · Sources checked November 2026

Short answer

A home driveway carrying cars and utes under 3 tonnes needs at least 100 mm of concrete with SL72 mesh, on the industry's published figures. Paths and patios that only take foot traffic start at 75 mm, and anything carrying vehicles of 3 to 10 tonnes needs 150 mm. The strip between your boundary and the kerb follows the council's own standard, which is a minimum of 100 mm in the City of Newcastle and 125 mm in Lake Macquarie. Shed and garage slabs are poured to the shed supplier's engineering.

How thick should a concrete driveway be?

For an ordinary home driveway, 100 mm. That figure comes from the data sheet on residential driveways and paths published by Cement Concrete and Aggregates Australia, the industry body for concrete, which sets a minimum of 100 mm for pavements used by vehicles under 3 tonnes gross mass. Cars, SUVs and most utes sit under that line.

The number is a minimum, and it assumes two things: that the vehicles really are under 3 tonnes, and that the ground under the slab gives even support. Change either and the answer changes, which is what the rest of this page is about. It also applies only inside your boundary. The piece of driveway between the boundary and the kerb belongs to council, and council sets its own figure.

Concrete slab thickness by use

These are the published minimums, with the steel and joint spacing that go with each. The first three rows are from the industry data sheet. The two crossing rows are from the councils’ own standards.

UseMinimum thicknessMeshJoints no further apart than
Paths and patios, foot traffic only75 mmSL522.0 m
Driveways, vehicles under 3 tonnes100 mmSL723.0 m
Vehicles of 3 to 10 tonnes150 mmSL925.0 m
Council crossing, City of Newcastle100 mm, 25 MPaSL72, top of slab3.0 m
Council crossing, Lake Macquarie125 mm, 25 MPaSL72, dowelled to the kerbSaw cut at the boundary
Shed and garage slabsTo the shed supplier’s engineeringTo the engineeringTo the engineering

Mesh sizes shown are the data sheet’s minimum for minor crack control. Where a decorative finish such as exposed aggregate makes fine cracks more visible, it lists a heavier mesh for each thickness. Pavements for vehicles over 10 tonnes need an engineer’s design.

What do Newcastle and Lake Macquarie councils require?

The crossing is where thickness stops being a matter of opinion. Each council publishes a standard, inspects against it, and holds the owner responsible for meeting it.

City of Newcastle. Standard drawing A1300 sets a residential crossing, single or double, at a minimum of 100 mm thick, reinforced with SL72 mesh placed in the top of the slab with 40 mm of cover, in concrete of 25 MPa at 28 days, with joints at no more than 3 metres.

Lake Macquarie City Council. The council’s driveway standard is heavier: a minimum of 125 mm with SL72 mesh in 25 MPa concrete, dowelled into the kerb with 12 mm bars every 600 mm, a full depth saw cut at the property boundary and an expansion joint between the layback and the driveway.

So a driveway in Charlestown or Cameron Park has a thicker crossing than the same driveway in Lambton or Fletcher, and a quote that prices 100 mm throughout in Lake Macquarie has not allowed for it. Both crossings need council approval before they are poured. The Section 138 guide explains how each council takes the application, and the areas page shows which council your suburb is in.

Does mesh make a thinner slab strong enough?

No, and this is the most common misunderstanding in residential concreting. The industry data sheet says it plainly: steel reinforcement or mesh does not increase the load capacity of a pavement and does not affect its thickness. Its job is to hold tightly closed any cracks that form.

In practice that means two things. A 75 mm slab with heavy mesh is still a 75 mm slab, and it will break under a vehicle where a 100 mm slab would not. And mesh only does its own job if it is in the right place: in the top half of the slab, with at least 30 mm of concrete over it, held up on bar chairs. Mesh laid on the ground and poured over ends up under the concrete, where it restrains nothing. Why concrete cracks in Newcastle covers what that looks like a few winters later.

When is 100 mm not enough?

When the vehicles are heavier than you think. The 100 mm figure stops at 3 tonnes gross. A large motorhome, a heavy caravan on its tow vehicle or a loaded tipper can pass it, and that moves the slab into the 150 mm class. Delivery trucks matter too. A loaded concrete truck weighs far more than 10 tonnes, which is why a concreter keeps it on the street and uses a chute or a pump rather than driving it across a new driveway.

When the ground is reactive clay. Thickness cannot make up for ground that moves. West of the city and across much of inland Lake Macquarie the soil is clay that swells when wet and shrinks when dry. For highly reactive clay sites the data sheet recommends a sub-base under the slab: at least 100 mm of low volume change material such as road base, compacted, and not sand or gravel. Its purpose is to keep moisture changes away from the clay and give the slab even support. The Housing Industry Association adds that the residential pavement standard, AS 3727.1, is written for the less reactive site classes, and recommends engineering advice outside them. Blocks in Cameron Park and Edgeworth are the kind where the base deserves as much attention as the slab.

At the edges and where wheels turn. An unsupported slab edge is its weakest point, and the place a wheel drops off a driveway is always an edge. Thickened edges are common where a driveway meets a garden bed, at the garage threshold and where cars turn on the spot.

Within a kilometre of the ocean. This one is about curing, not millimetres, but it decides whether the thickness you paid for reaches its strength. The data sheet asks for at least 3 days of curing for residential pavements and 7 days where the slab is within 1 km of the coast or will carry heavier traffic. The beach end of Merewether and the streets behind the Newcastle beaches fall inside that line.

How thick should a shed or garage slab be?

Whatever the shed supplier’s engineering says. A shed slab is a footing for a building as well as a floor, so its thickness, mesh, edge thickening and hold-down positions come with the kit, and a slab poured to those drawings lets the frame go up square. A garden shed holding a mower is a different slab from a workshop with a car hoist in it.

The site’s dedicated guide covers shed slab thickness and cost with worked prices for common shed and garage sizes, and the service page for shed and garage slabs explains rebates, falls and getting concrete to a back corner. Slabs under dwellings are a separate, engineered and certified process and are not covered here.

How much concrete is that?

Volume is area multiplied by thickness, with the thickness in metres.

  • 40 m² driveway at 100 mm: 40 x 0.10 = 4.0 m³
  • The same driveway at 125 mm: 40 x 0.125 = 5.0 m³
  • The same driveway at 150 mm: 40 x 0.15 = 6.0 m³
  • 15 m² side path at 75 mm: 15 x 0.075 = 1.1 m³

Going from 100 mm to 125 mm adds a quarter more concrete, and going to 150 mm adds half as much again. That extra concrete is real money, which is exactly why thickness is the first thing to shrink in a low quote and why it has to be written down.

What does thickness do to the price?

The published guide rates on this site are per square metre, supplied and laid: concrete driveways $95 to $130 in plain concrete, $115 to $160 coloured and $130 to $185 in exposed aggregate, paths $90 to $130, patios and alfresco slabs $100 to $180, and shed and garage slabs $110 to $150. Thickness is one of the things that moves a job within its range, along with access, ground preparation and finish. A Lake Macquarie crossing at 125 mm, or a hardstand built for a motorhome at 150 mm, sits higher than a standard 100 mm driveway for the same area.

A low price and a high price for one driveway are often prices for two different thicknesses. The cost guide shows worked examples, and the calculator will bracket your own job from its length and width. Published rates are a guide for budgeting. The price for your job is the one on the written quote after a site measure.

What should the quote say?

Ask for six things in writing before you accept any price:

  1. Thickness of the driveway, and of the crossing if it is included.
  2. Concrete strength, in MPa.
  3. Mesh size, and that it is supported on bar chairs.
  4. Base preparation, including what happens if soft or reactive ground is found.
  5. Joint spacing and where the joints will run.
  6. Who prepares and lodges the council application for the crossing.

Then hold the answers against this page and the site’s specification. If an old slab is coming out first, removal and replacement adds about $35 per m², and it is the one chance to see how thick the old concrete really was.

Sources, checked November 2026

Cement Concrete and Aggregates Australia, data sheet “Residential Concrete Driveways and Paths” (thickness by use, reinforcement and joint spacing table, mesh position and cover, sub-base on highly reactive clay, curing periods). Housing Industry Association, “Designing pavements to avoid cracking”, 24 May 2022 (AS 3727.1 as guidance, site classes). City of Newcastle standard drawing A1300, Driveway Crossing Standard Design Details, revision 2. Lake Macquarie City Council, Driveways page, residential driveway standard. These documents give general industry and council minimums, not a design for a particular site. Councils and industry bodies update them without notice, and the council’s approval letter and the concreter’s written quote govern the job.

Asked and answered

Questions people ask

How thick should a concrete driveway be in Australia?

The industry data sheet published by Cement Concrete and Aggregates Australia gives a minimum of 100 mm for pavements carrying vehicles under 3 tonnes gross mass, which covers ordinary cars and utes, and 150 mm for vehicles between 3 and 10 tonnes. Anything heavier needs an engineer's design. Councils set their own figure for the crossing at the kerb, so check that separately.

Is 75 mm thick enough for a concrete path?

For a path or patio that only ever carries people, yes. 75 mm is the published minimum for foot traffic. The catch is the word only. If a car, a trailer or a ride-on mower will cross it, even now and then, that section should be built as a driveway at 100 mm with mesh. Many concreters pour side paths at 100 mm for that reason.

What is the minimum thickness for a driveway crossing in Newcastle and Lake Macquarie?

City of Newcastle's standard drawing A1300 sets a minimum of 100 mm for a residential crossing, with SL72 mesh in the top of the slab and 25 MPa concrete. Lake Macquarie City Council sets a minimum of 125 mm with SL72 mesh and 25 MPa concrete, dowelled into the kerb. Each council's approval letter can ask for more on a particular site.

Does steel mesh mean the slab can be thinner?

No. The industry data sheet is direct about it. Reinforcement does not increase the load a pavement can carry and does not change the thickness it needs. Mesh is there to hold any cracks tightly closed so they stay fine and level. Carrying the load is the job of the concrete's thickness and the ground under it.

How do I work out how much concrete a slab needs?

Multiply the area in square metres by the thickness in metres. A 40 square metre driveway at 100 mm is 40 x 0.1, which is 4 cubic metres. The same driveway at 125 mm is 5 cubic metres, and at 150 mm it is 6. Concreters order a little over to allow for uneven ground and thickened edges.

Do I need thicker concrete for a caravan, boat or motorhome?

Go by gross weight, not by the type of vehicle. Under 3 tonnes, the 100 mm figure applies. A large motorhome, a heavy caravan or a loaded truck can pass 3 tonnes, which moves the slab into the 150 mm class. Check the compliance plate, tell the concreter what will park there, and have the thickness written into the quote.

Next step

Get a quote that states the thickness

Newcastle Concreters is a referral service. Enquiries are passed to an independent local concreter, who measures the job, quotes it in writing and carries out the work.

Request a measure and quote

Say what you want poured and where. A local concreter rings back to arrange the site measure.

Prefer to talk? (02) 4071 4720

Call (02) 4071 4720 Get a quote